|
|
Main
>
Camera chain with remote controls
|
3G/HD SDI camera control system.
PFC-01 /PFB-02 series
|
PFC-01 / PFB-02 series devices allow to organize a
fiber-optic camera channel for connecting a remote camera to a base
station, with the ability to control robotized objects using one or two
fibers. These devices are always paired. PFC-01 series device
(Camera Adapter (CA)) is located at the camera, ànd PFB-02
series device (Base Station (BS)) – on the outside broadcasting
unit (OBU).
System functionality
-
Bidirectional
transmission of 3G/HD/SD SDI
-
Transport of four
audio channels from the camera and their output to the BS (linear analog
inputs/outputs or two AES/EBU inputs/outputs)
-
Intercom line
-
Microphone or line
input, telephone or line output (CA) PFC-01
-
Line input, line
output (BS) PFB-02
-
Three independent
two-way data ports with baud rate up to 115200 Baud
-
RS-232, RS-422, RS-485/4WIRE, RS-485/2WIRE …...port 1
-
RS-232, RS-422, RS-485/4WIRE, RS-485/2WIRE …...port 2
-
LANC…………………………………………...port 3
-
The choice of interface type (port 1, 2) is determined by
the contacts on the DATA connector
-
Three TALLY signals
transport from BS PFB-02 to CA (relay, “dry” closure outputs) PFC-01
-
100/1000 Ethernet
line with integrated dual-port switch
-
Single- or dual-fiber version
-
Optical budget up to 23 dB
-
Power supply DC
10,5…17 V, max 4,8 W
The following pairs of devices are available, depending on
the number of fibers, the optical budget and availability of Ethernet interface
(see Table 1):
Table 1
|
Ethernet |
#Fibers |
Budget,
dB |
Audio format:
A - analog,
D - AES/EBU |
Camera Adapter |
Base Station |
Tx Optical
Power, dBm |
Rx Optical
Power, dBm ## |
|
100/1000 |
2 |
15 |
x (A or D) |
PFC-O1-E-2F-15-x-(VM) |
PFB-O2-E-2F-15-x |
0…-5 |
-3…-20 |
|
100/1000 |
2 |
23 |
x (A or D) |
PFC-O1-E-2F-23-x-(VM) |
PFB-O2-E-2F-23-x |
0…+3 |
-9…-23 |
|
100/1000 |
1 |
15 |
x (A or D) |
PFC-O1-E-1F-15-x-(VM) |
PFB-O2-E-1F-15-x |
0…-5 |
-3…-20 |
|
100/1000 |
1 |
23 |
x (A or D) |
PFC-O1-E-1F-23-x-(VM) |
PFB-O2-E-1F-23-x |
0…+3 |
-9…-23 |
|
--- |
1 |
15 |
x (A or D) |
PFC-O1-1F-15-x-(VM) |
PFB-O2-1F-15-x |
0…-5 |
-3…-20 |
|
--- |
1 |
23 |
x (A or D) |
PFC-O1-1F-23-x-(VM) |
PFB-O2-1F-23-x |
0…+3 |
-9…-23 |
##....ATTENTION!
Do not overload the optical input
to avoid permanent damage. If the input optical power exceeds the upper limit –
AN OPTICAL ATTENUATOR IS NECESSARY..
Dual-fiber functional diagram
Single-fiber functional diagram
Technical specifications PFC-01 series Camera Adapter
3G/HD/SD SDI INPUT (camera signal input):
|
Supported standards |
SMPTE 424M/ SMPTE 425M
(3G Level A 4:2:2):
1080p/50;
1080p/59. 94;
1080p/60.
SMPTE 292M (HD SDI):
1080i/50;
1080i/59. 94;
1080i/60;
1080p/23.98.
1080p/24;
1080p/25;
1080p/29. 97;
1080p/30;
720p/50;
720p/59. 94;
720p/60.
SMPTE 259M (SDI):
625i/50;
525i/59.94. |
|
Number of audio groups in
the input SDI |
SDI embed, Group 1+ Group 2 max |
|
Connector |
BNC |
|
Input impedance |
75 Ohm |
|
Automatic cable input
correction
3G
HD
SD |
up to 100 m (for cable
1694A or equivalent)
up to 150 m
up to 300 m
|
Analog audio input:
|
Connector |
DB-15F (female) |
|
Input impedance |
Not less 10 kΩ |
|
Number of channels, input
type |
2 stereopairs, symmetric
input, balanced |
|
Dynamic range |
not less 100 dB |
|
Nonlinear distortion +
noise |
not more 0.009% |
|
Digital-to-analog
conversion |
24 bits
|
|
Sampling rate |
48 kHz video referenced |
Digital audio input AES/EBU
|
Connector |
DB-15F (female) |
|
Number of channels, input
type |
Two, input balanced,
transformer |
|
Peak-to-peak amplitude |
(0.2 … 4.0) V |
|
Input impedance |
110 Ohm |
SDI OUT (BS signal output):
|
Number of outputs |
1 |
|
Connector |
BNC |
|
Output impedance |
75 Ohm |
|
Standard |
complies with BS output
signal standard |
|
Output return loss |
not less 10 dB up to 3
GHz |
|
Peak-to-peak amplitude |
800 mV±10% |
|
Jitter |
less than 0.2UI (unit
interval) |
Intercom line
|
Input type,
user-selectable |
-Microphone, dynamic
microphone
-Microphone, electret
microphone
-line, nominal level 0
dBu |
|
Output type,
user-selectable |
-Telephone, with volume
control
-line, nominal level 0
dBu |
|
Microphone input AGC
nominal level (SENSE) |
-6…+2 dBu |
|
Connector |
XLR 5 pin, NC5FAH
(female) |
Data transmission
|
Port 1, interface type is
determined by contacts in
DHR-26F connector |
RS-232, RS-422,
RS-485/4WIRE,
RS-485/2WIRE, connector
DHR-26F (female) |
|
Port 2, interface type is
determined by contacts in
DHR-26F connector |
RS-232, RS-422, RS-485,
RS-485/2WIRE,
connector DHR-26F
(female) |
|
Port 3 |
LANC, Jack 3.5 mm
connector |
|
Baud rate |
max 115200 Baud |
Tally output
|
Number of Tally output
ports |
Three |
|
Type |
Relay, “dry” closure,
two contacts per one Tally port, normally opened |
|
Switched signals
characteristics |
- max switched power:
10 W;
- max switched
voltage: 100 V;
- max switched
current: 0.5 A. |
|
Connector |
DHR-26F (female) |
100/1000 Ethernet transport
|
Standard |
IEEE 802.3i 10 Base-T,
IEEE 802.3u 100 Base-T,
IEEE
802.3ab 1000 Base-TX |
|
Connector |
RJ-45, dual-port switch |
|
Cable |
UTP cable, Cat-5, max 100
m |
Optical inputs/outputs
|
Connector |
ST/UPC |
|
Fiber |
Single mode |
|
Number of fibers |
One or two, in accordance
with Table 1 |
|
Optical budget |
23 dB or 15 dB, in
accordance with Table 1 |
|
Maximum distance
(typical) |
80 km or 50 km
respectively |
Power supply
|
Connection |
XLR, 4 pin, NC4MAH (male) |
|
Voltage |
DC 10.5V…17V, with
overvoltage and reverse power supply polarity protection |
|
Power consumption |
less than 5W |
Operation temperature range:
from -25°Ñ to 45°Ñ.
Continuous running time:
24 hours.
Overall dimensions:
146 õ201õ42 mm (WõLõH).
Mass: less than 1
kg.
PFC-01 camera adapter Indication and Control
PFC-01-2F camera adapter front panel (dual-fiber)
PFC-01-1F camera adapter front panel (single-fiber)
|
Microswitch. Power-on
Power |
Indication. LED, green |
|
Button MIC |
Intercom input type
selection |
|
Intercom input |
Line
(line input). LED, green
Dynamic
(dynamic microphone). LED, green
Electr (electret
microphone). LED, green |
|
Button OUT |
Intercom output type
selection |
|
Intercom output |
Line
(line output). LED, green
Phone
(telephone). LED, green |
|
Sense.
AGC nominal level setting on
microphone input
|
-6 dBu …+2 dBu |
|
Volume.
Phone Volume control. |
-56 dBu …+6 dBu |
|
Button MIC EN with
integrated green LED. |
Microphone input enable |
|
SDI in |
Camera signal presence.
LED, green |
|
A1/2.
Channels are embedded in
the third group |
Audio level in channels 1
and 2 is more than -30 dBu. LED, green |
|
A3/4.
Channels are embedded in the third group |
Audio level in channels 3
and 4 is more than -30 dBu. LED, green |
|
Data 2 |
Data transmission occurs
at port 2. LED, green |
|
Data 1 |
Data transmission occurs
at port 1. LED, green |
|
Link |
Stable communication
established with BS |
|
SDI Tx Fault |
SDI transmitter optical
power dropped below -5 dB. |
|
Eth Tx Fault |
Ethernet transmitter
optical power dropped below -5. |
|
Eth -7, SDI -7 |
Input optical power in
Ethernet and SDI line, respectively, is in range 0..-7 dB |
|
Eth -14, SDI -14 |
Input optical power in
Ethernet and SDI line, respectively, is in range -7..-14 dB |
|
Eth -18, SDI -18 |
Input optical power in
Ethernet and SDI line, respectively, is in range -14..-18 dB |
|
Eth -25, SDI -25 |
Input optical power in
Ethernet and SDI line, respectively, is in range -18..-25 dB |
|
Eth LOSS, SDI LOSS
|
No optical radiation at
the input or it below threshold in Ethernet and SDI line, respectively. |
PFC-01 camera adapter connector pinouts
PFC-01-2F/1F camera adapter rear panel
PFC-01 Audio inputs, DB-15F (female) connector
|
|
Analog inputs |
AES inputs |
DB-15F |
|
Ch. 1 - |
AES1- |
1 |
|
Ch. 1 + |
AES1+ |
2 |
|
GND |
GND |
9 |
|
Ch. 2 - |
|
10 |
|
Ch. 2+ |
|
11 |
|
GND |
|
3 |
|
Ch. 3 - |
AES2- |
4 |
|
Ch. 3 + |
AES2+ |
5 |
|
GND |
GND |
12 |
|
Ch. 4 - |
|
13 |
|
Ch. 4+ |
|
14 |
|
GND |
|
6 |
PFC-01 Intercom, XLR 5pin connector NC5FAH (female)
PFC-01 RS-232/422/485 Data, Tally, DHR-26F (female)
connector
PORT 1. To establish the required
interface, pins 14 and 5 should be connected to pin 20 in accordance with the
table below.
|
PIN |
1 |
10 |
2 |
11 |
19 |
14
RS1 -232/422 SEL |
5
RS1_HDPLX |
|
RS-232 |
NC |
RX |
GND |
TX |
NC |
GND (20) |
NC |
|
RS-422/485 |
-RX1 |
+RX1 |
GND |
-TXOUT1 |
+TXOUT1 |
NC |
NC |
|
RS-485/2W |
|
|
GND |
-D(B)/1 |
+D(A)/1 |
NC |
GND (20) |
PORT 2. To establish the required
interface, pins 15 and 6 should be connected to pin 22 in accordance with the
table below.
|
PIN |
3 |
12 |
4 |
13 |
21 |
15
RS2 -232/422 SEL |
6
RS2_HDPLX |
|
RS-232 |
NC |
RX |
GND |
TX |
NC |
GND (22) |
NC |
|
RS-422/485 |
-RX2 |
+RX2 |
GND |
-TXOUT2 |
+TXOUT2 |
NC |
NC |
|
RS-485/2W |
|
|
GND |
-D(B)/2 |
+D(A)/2 |
NC |
GND (22) |
|
Tally
|
Not Connect |
|
Functional |
PIN |
|
NC |
23 |
|
NC |
24 |
|
NC |
25 |
|
|
Functional |
PIN |
|
TALLY1_A |
16 |
|
TALLY1_B |
7 |
|
TALLY2_A |
17 |
|
TALLY2_B |
8 |
|
TALLY3_A |
18 |
|
TALLY3_B |
9 |
|
GND |
26 |
|
PFC-01 POWER, XLR 4pin connector NC4MAH (male)
Technical specifications PFB-02 series Base Station
3G/HD/SD SDI INPUT (ÂS signal input):
|
Supported standards |
SMPTE 424M/ SMPTE 425M
(3G Level A 4:2:2):
1080p/50;
1080p/59. 94;
1080p/60.
SMPTE 292M (HD SDI):
1080i/50;
1080i/59. 94;
1080i/60;
1080p/23.98.
1080p/24;
1080p/25;
1080p/29. 97;
1080p/30;
720p/50;
720p/59. 94;
720p/60.
SMPTE 259M (SDI):
625i/50;
525i/59.94. |
|
Number of audio groups in
the input SDI |
SDI embed, Group 1+ Group 2 max |
|
Connector |
BNC |
|
Input impedance |
75 Ohm |
|
Automatic cable input
correction
3G
HD
SD |
up to 100 m (for cable
1694A or equivalent)
up to 150 m
up to 300 m
|
SDI OUT (CAMERA signal output):
|
Number of outputs |
1 |
|
Connector |
BNC |
|
Output impedance |
75 Ohm |
|
Standard |
complies with ÑÀ output
signal standard |
|
Output return loss |
not less 10 dB up to 3
GHz |
|
Peak-to-peak amplitude |
800 mV±10% |
|
Jitter |
less than 0.2UI (unit
interval) |
Analog audio output:
|
Connector |
DHR-26F (female) |
|
Output impedance |
<50 Ohm |
|
Output type |
symmetric |
|
Output dynamic range,
corresponding 0 dB Fs |
+18 dB |
|
Dynamic range |
not less 100 dB |
Digital audio output
|
Connector |
DHR-26F (female) |
|
Output type |
symmetric, transformer |
|
Peak-to-peak amplitube |
3V on 110 Ohm load |
Intercom line
|
Input type |
-line, nominal level 0
dBu |
|
Output type |
-line, nominal level 0
dBu |
|
Connector |
XLR 5 pin, NC5FAH
(female) |
Data transmission
|
Port 1, interface type is
determined by contacts in
the DHR-26F connector
|
RS-232, RS-422,
RS-485/4WIRE,
RS-485/2WIRE,
DHR-26F connector
(female) |
|
Port 2, interface type is
determined by contacts in
the DHR-26F connector |
RS-232, RS-422,
RS-485/4WIRE,
RS-485/2WIRE,
DHR-26F connector
(female) |
|
Port 3 |
LANC, Jack 3.5 mm
connector |
|
Baud rate |
max 115200 Baud |
Tally inputs
|
Number of Tally input
ports |
Three |
|
Type |
Contact closure to GND |
|
Connector |
DHR-26F (female) |
100/1000 Ethernet transport
|
Standard |
IEEE 802.3i 10 Base-T,
IEEE 802.3u 100 Base-T,
IEEE
802.3ab 1000 Base-TX |
|
Connector |
RJ-45, dual-port switch |
|
Cable |
UTP cable, category 5,
max 100 m |
Optical inputs/outputs
|
Connector |
ST/UPC |
|
Fiber |
Single mode |
|
Number of fibers |
One or two, in accordance
with Table 1 |
|
Optical budget |
23 dB or 15 dB, in
accordance with Table 1 |
|
Maximum distance
(typical) |
80 km or 50 km
respectively |
Power supply
|
Connector |
XLR, 4 pin, NC4MAH (male) |
|
Voltage |
DC 10.5V…17V, with
overvoltage and reverse power supply polarity protection |
|
Power consumption |
less than 5W |
Operation temperature range:
from -25°Ñ to 45°Ñ.
Continuous running time:
24 hours.
Overall dimensions:
146 õ201õ42 mm (WõLõH).
Mass:
less than 1
kg.
PFB-02 base station Indication and Control
PFB-02-E-2F base station front panel (dual-fiber)
PFB-02-E-1F base station front panel (single fiber)
|
Microswitch. Power-on
Power |
Indication. LED, green |
|
SDI in |
Signal from Base Station
present. LED, green |
|
A1/2.
Extracting from the third
group. |
Audio level in channels 1
and 2 of the third group
is more than -30 dBu.
LED, green |
|
A3/4.
Extracting from the third group. |
Audio level in channels 3
and 4 of the third group
is more than -30 dBu.
LED, green |
|
Data 2 |
Data transmission occurs
at port 2. LED, green |
|
Data 1 |
Data transmission occurs
at port 1. LED, green |
|
Link |
Stable communication with
camera side established |
|
SDI Tx Fault |
SDI transmitter optical
power dropped below -5 dB. |
|
Eth Tx Fault |
Ethernet transmitter
optical power dropped below -5 dB. |
|
Eth -7, SDI -7 |
Input optical power in
Ethernet and SDI line,
respectively, is in range 0..-7 dB |
|
Eth -14, SDI -14 |
Input optical power in
Ethernet and SDI line, respectively, is in range -7..-14 dB |
|
Eth -18, SDI -18 |
Input optical power in
Ethernet and SDI line, respectively, is in range -14..-18 dB |
|
Eth -25, SDI -25 |
Input optical power in
Ethernet and SDI line, respectively, is in range -18..-25 dB |
|
Eth LOSS, SDI LOSS
|
No optical signal at the
input or is below threshold in Ethernet and SDI line, respectively. |
PFB-02 base station connectors pinouts
PFB-02-E-2F/1F base station rear panel
PFB-02 Audio outputs, DB-15F (female) connector
|
|
Analog outputs |
AES outputs |
DB-15F |
|
Ch. 1 - |
AES1- |
1 |
|
Ch. 1 + |
AES1+ |
2 |
|
GND |
GND |
9 |
|
Ch. 2 - |
|
10 |
|
Ch. 2+ |
|
11 |
|
GND |
|
3 |
|
Ch. 3 - |
AES2- |
4 |
|
Ch. 3 + |
AES2+ |
5 |
|
GND |
GND |
12 |
|
Ch. 4 - |
|
13 |
|
Ch. 4+ |
|
14 |
|
GND |
|
6 |
PFB-02 Intercom, XLR 5pin connector NC5FAH (female)
PFB-02 RS-232/422/485 Data,
Tally, DHR-26F (female) connector
PORT 1. To
establish the required interface, pins 14 and 5 should be be connected to pin 20
in accordance with the table below.
|
PIN |
1 |
10 |
2 |
11 |
19 |
14
RS1
-232/422 SEL |
5
RS1_HDPLX |
|
RS-232 |
NC |
RX |
GND |
TX |
NC |
GND (20) |
NC |
|
RS-422/485 |
-RX1 |
+RX1 |
GND |
-TXOUT1 |
+TXOUT1 |
NC |
NC |
|
RS-485/2W |
|
|
GND |
-D(B)/1 |
+D(A)/1 |
NC |
GND (20) |
PORT 2. To
establish the required interface, pins 15 and 6 should be be connected to pin 22
in accordance with the table below.
|
PIN |
3 |
12 |
4 |
13 |
21 |
15
RS2
-232/422 SEL |
6
RS2_HDPLX |
|
RS-232 |
NC |
RX |
GND |
TX |
NC |
GND (22) |
NC |
|
RS-422/485 |
-RX2 |
+RX2 |
GND |
-TXOUT2 |
+TXOUT2 |
NC |
NC |
|
RS-485/2W |
|
|
GND |
-D(B)/2 |
+D(A)/2 |
NC |
GND (22) |
|
Not Connect
|
Tally In |
|
Functional |
PIN |
Execute |
|
Tally In 1 |
23 |
Connect pin to GND |
|
Tally In 2 |
24 |
Connect pin to GND |
|
Tally In 3 |
25 |
Connect pin to GND |
|
GND |
26 |
|
|
|
Functional |
PIN |
|
NC |
16 |
|
NC |
7 |
|
NC |
17 |
|
NC |
8 |
|
NC |
18 |
|
NC |
9 |
|
PFB-02 Power, XLR 4 pin NC4MAH
(male) connector
|
