|
|
Main / LOGO generator-inserters / PNLG-3324
PNLG-3324(E) series SDI/YUV/RGB/PAL/SECAM/YC=>SDI/YUV/PAL/SECAM/YC logo-mixer and synchronizer |
PROFLEX™ PNLG-3324(E) series logo-mixer and synchronizer accepts the SDI/YUV/RGB/PAL/SECAM/YC (625/50) video signals, converts into the SDI/YUV/PAL/SECAM/YC (625/50) standards video, generates and inserts the LOGO and/or scrolling text video into the output signal with the synchronization to external REF reference video.
Two modifications exist:
- PNLG-3324 – with RS-232 interface;
- PNLG-3324E – with Ethernet network connectivity.
The PNLG-3324 module occupies two slots in a PROFLEX rack.
Technical speficications
- Inputs
- SDI/Y/G/CCVS1 input:
- SDI
| standard compliance |
D1 (270 MB/s) ITU-R 656 |
| input impedance |
75 Ohm |
| return loss |
better than 15dB at 270MHz |
| signal amplitude |
800±80mV |
| automatic cable equalization |
up to 300 meters |
- Y, G, CCVS1
- Y and G signals should contain synchro pulses
- input impedance 75 Ohm
- signal amplitude 1V
- Pb/B/C/CCVS2
- input impedance 75 Ohm
- Pb signal amplitude 525mV
- B and CCVS2 signal amplitude 1V
- C signal amplitude 670mV
- Pr/R
- input impedance 75 Ohm
- Pr signal amplitude 525mV
- R signal amplitude 1V
- REF video input
- pass-through, two BNC connectors
- high impedance
- enabled by X6 jumper setting (EXT REF/GLOB REF)
- Outputs (four BNC connectors: Y/SDI/CCVS, Pr/SDI/CCVS/C, Pb/SDI/CCVS and PAL PVW)
- SDI mode
| standard compliance |
D1 (270 MB/s) ITU-R 656 |
| output impedance |
75 Ohm |
| return loss |
better than 15dB at 270MHz |
| signal amplitude |
800±80mV |
| jitter |
less than 700ps |
- YUV output mode
- Y signal amplitude 1V at 75 Ohm
- Pr and Pb signals' amplitude 525mV at 75 Ohm
- PAL/SECAM output mode
- output impedance 75 Ohm
- signal amplitude 1V
- YC output mode
- output impedance 75 Ohm
- C signal amplitude 670mV at 75 Ohm
- Y signal amplitude 1V at 75 Ohm
- PAL PVW video output
- output impedance 75 Ohm
- signal amplitude 1V
- Controls
- GPI IN
- DUB-15F connector
- a command is activated by temporarily grounging an input
- RS-232/Ethernet
- RJ-45 connector
- RS-232 input/output (for PNLG-3324)
- Ethernet twisted pair (for PNLG-3324E)
Features
PNLG-3324 simplified schematics
Input signal processing
10-bits digital processing, analog input signals undergo the digital comb-filtering.
The SDI input signal's content quality is not affected during the processing.
| Sampling |
10-bits at 27MHz |
| LUMA channel frequency response ripple, up to 5,8MHz, YUV/RGB/YC mode |
less than 0,5dB |
| LUMA channel frequency response ripple, PAL/SECAM mode |
| SECAM |
2,2MHz |
2,9MHz |
3,9...4,7MHz |
5,8MHz |
| -0,3dB |
< -3dB |
> -40dB |
-1,5dB |
| PAL |
less than 0,5dB up to 5,8MHz |
| return loss |
better than 40dB at 4,43MHz |
| diff phase |
less than 0,2 ° |
| diff gain |
less than 0,2% |
| SNR (weighted) |
> 65dB |
| V tilt |
< 0,5% |
| 2Ò K-factor |
less than 0,5% |
Output signal processing
The PAL/SECAM encoding and YC generation is provided in digital domain with the 12-bits resolution.
The PAL, SECAM, YC and YUV signals' parameters comply with the GOST 7845-92 and ITU-R BT.601-5 specifications.
LOGO-generator features and capabilities:
To design, edit and load the LOGOs and scrolling texts for the PNLG-3324 the software package is required (MS Windows only).
- Logo
- Graphical logo:
- 24-bits color depth (16M colors)
- 256 grades of opacity
- non-volatile logo storage capacity: four TV frames
- eight simultaneously loaded logo's
- 720x576 pixel maximum logo resolution
- 255 movement phases for a dynamic logo
- Textual logo:
- texts with time/date, weather information, etc, displayed with the preloadable fonts
- user-editable fonts and color palettes
- up to seven different fonts to use simultaneously
- 62x60 pixels maximum font placeholder
- sixteen different foreground and background colors simultaneously
- up to eight textual constants, 32 symbols each
- up to eight scenes each composed of up to five simultaneous logos: one graphical and four textual
- capability to overlay a graphic and a textual logo
- scene control: ON/OFF, scene selection and swap/mix with presettable scheduling option
- Scrolling text logo:
- externally loadable content: live from a PC, ON/OFF by a local or GPI command
- up to 99 internally stored scrolling lines 30 000 symbols total, selection from a local or remote panel, from a PC or by GPI command
- two display modes of the internally stored lines: "show once" and "in cycle"
- user-editable fonts and foreground/background color palettes
- up to seven different fonts to use simultaneously
- 62x60 pixels maximum font placeholder
- sixteen different foreground and background colors simultaneously
- 256 grades of opacity
- capability to overlay/mix the scrolling line on top of graphic and text logos
- presettable on-screen position and scrolling speed with the scheduling option
PNLG-3324 controls and indicators
PNLG-3324 consists of the two submodules: the frontal one, with all the controls and indicators, and the rear one, with all the connectivity means.
PNLG-3324 rear panel view
PNLG-3324 frontal panel view
Controls:
- MODE - toggles through all the modes,
- UP and DOWN buttons edit them
Press the DOWN and UP buttons simultaneously to reset a parameter to it's default value.
- CL – toggles the scrolling text/line mode ON/OFF
Indicators:
At the frontal edge of the board the two status LEDs are located:
- INP – lit when an input signal is present
- REF – lit when the REF signal is present (if synchroniser is enabled)
The main indication board contains:
- OPTION – lit when the main seven-segment LED dispalys whether the LOGO or synchronizer parameters are being preset
The standard converter's/synchroniser's controls menu
- INP – lit when the input mode (SDI, CCVS 1, CCVS 2, YUV , RGB , Y/C) is being selected with the DOWN/UP buttons. The modes are shown at the main LED as SDI – SdI, YUV – YUu, RGB – rGb, Y/C – YC respectively. The CCVS 1 or CCVS 2 input mode is displayed as PAL or SECAM, autodetectable by the decoder as follows:
- 1 SE – the SECAM signal is present at the CCVS 1 input
- 1 PL – the PAL signal is present at the CCVS 1 input
- 2 SE – the SECAM signal is present at the CCVS 2 input
- 2 PL – the PAL signal is present at the CCVS 2 input
- OUT – lit when the output mode (SDI, CCVS 1, CCVS 2, YUV , RGB , Y/C) is being selected with the DOWN/UP buttons. The modes are shown at the main LED as SDI – SdI, YUV – YUu, PAL – PAL, SECAM – SEC, Y/C – YC respectively.
- BLCK ( BLACK ) – is lit when the LUMA's channel black level is being adjusted (in the ± 70mV range) with the DOWN/UP buttons. The level is shown as ±99 points. In the SDI mode is not available.
- CHR ( CHROMA ) – is lit when the saturation level is being adjusted (in the +5...-13dB range) with the DOWN/UP buttons. The level is shown as ±99 points. In the SDI mode is not available.
- GAIN – lit when the LUMA gain is being adjusted (in the +1.8...-2.5dB range) with the DOWN/UP buttons. The level is shown as ±32 points. In the SDI mode is not available.
- TIME H and TIME V – lit when the timing of the output signal is being adjusted relative to the REF video (H – within a TV line, ±32µs range, V – within a TV frame, ±99 TV lines). (if synchroniser is enabled)
- SC – lit when the PAL/YC subcarrier phase is being adjusted within the 360° range (except the PNLG-3324). The YUV mode: depending on the S1.6 DIP switch setting - the Y output H-sync puls timing may be adjusted within (+7...-8)* 74ns range, depending on the S1.5 DIP switch setting - the Y output H-blancing puls timing may be adjusted within (+7...-8)* 74ns range
- VBI – lit when the VBI-pass-through options are preset (teletext, VITC, etc):
- PAS – VBI pass-through is ENABLED
- BLA – VBI contents is blanced
- REF – VBI contents is being transferred from the REF video into the output signal
- VITS – not implemented in the PNLG-3324
- TEST – lit when a test signal type is being selected for the frame's active lines:
- oFF - test signals are OFF
- brh - vertical color bars
- bru - horizontal color bars
- L 1, L 2, L 3, L 4 - the I , II , III , IV test-signals (according to GOST 18471-83)
VITS number (according to the GOST 18471-83) is being shown on the main indicators.
The LOGO/scrolling texts controls menu
(on the gray-shaded markers)
- YEAR – lit when the calender year value is being preset
- MON – lit when the calender month value is being preset
- DATE – lit when the calender day value is being preset
- HOUR – lit when the clock hour value is being preset
- MIN – lit when the clock minute value is being preset
- L ON – displays the ON/OFF status of the preselected LOGO-scene at the program output
- L SEL – lit when the scene number is being selecter
- CL RUN – lit when the scrolling text is enabled
- CL ON – displays the ON/OFF status of the preselected scrolling line at the program output
- CL SEL –lit when the scrolling text sample number is being selected
- CL SET – displays the number of the preselected scrolling line
All the settings are stored in a non-volatile memory.
The remote control and management from a PC
All the PROFLEX™ modules are remote controllable from a PC. This facility is available if a rack is fitted with a CPU module (ordered separately).
|
